TSST SU-228GB ODD Driver
Slim Tray Rambo ODD. 5DX0G **. 12 ODD, Rambo, TSST SUGB Rambo ODD. 5DX0H **. 13 FAN L IBD 5F10K N. TSSTcorp DVD+--R +6 3 %. - TSSTcorp DVDWBD +6 2 % hp TSST - DVDRW SUHB +6 2 % TOSHIBA - ODD-DVD SDRN + 1 %. TOSHIBA . TSSTcorp - CDDVDW SUGB +6 2 %. TSSTcorp. todos los tornillos, muelles y demás piezas pequeñas se encuentran en su sitio y no se Removal steps of ODD board .. TSST SUGB Rambo ODD.
|Supported systems:||Windows 10, Windows 8.1, Windows 7|
|Price:||Free* [*Free Registration Required]|
TSST SU-228GB ODD Driver
If any unsafe conditions are present, you must determine how serious the apparent hazard could be and whether you can continue without first correcting the problem. Consider these conditions and the safety hazards they present: Begin the checks with the power off, and the power cord disconnected. Check exterior covers for damage loose, broken, TSST SU-228GB ODD sharp edges. Turn off the computer.
Disconnect the power cord. Check the power cord for: A third-wire ground connector in good condition. Remove them in the order in which they are listed.
Follow the correct sequence in the steps to remove the FRU, as given in the figures by the numbers in square callouts. When turning a screw to replace an FRU, turn it in the direction as given by TSST SU-228GB ODD arrow in the figure.
When TSST SU-228GB ODD the FRU, move it in the direction as given by the arrow in the figure. To put the new FRU in place, reverse the removal procedures and follow any of the notes that pertain to replacement.
When replacing an FRU, use the correct screw as shown in the procedures. DANGER Before removing any FRU, turn off the computer, unplug all power cords from electrical outlets, remove the battery pack, and then disconnect any TSST SU-228GB ODD the interconnecting cables.
After replacing an FRU, do not TSST SU-228GB ODD on the computer until you have made TSST SU-228GB ODD that all screws, springs, and other small parts are in place and none are loose inside the computer. Verify this by shaking the computer gently and listening for rattling sounds. Metallic parts or metal flakes can cause electrical short circuits. The system board is sensitive to, and can be damaged by, electrostatic discharge. Removal steps of keyboard Remove three screws a.
Removal steps of keyboard continued Lift up the keyboard d and disconnect the connector in the direction shown by arrows e f.
Lenovo IBR (ideapad) Hardware Maintenance Manual Page: 78
Be careful not to damage the connector. Make sure that the keyboard connector is attached firmly to the system board.
- Lenovo IBR (ideapad) Hardware Maintenance Manual Page: 78
- TSSTcorp CDDVDW SUGB not working after Fall Creators Update - Microsoft Community
- Lenovo B5050 En Hmm B50 50 User Manual Hardware Maintenance Laptop (Lenovo) Type 80S2
- Lenovo ideapad 110-14 15 Series Hardware Maintenance Manual Page 73
- TSSTCorp Drivers Download to Fix Problems on Windows 10, 8.1, 8, 7, XP, Vista
Removal steps of optical drive Remove the screw a. Then remove the optical drive by arrow b. Removal TSST SU-228GB ODD of optical drive continued Unsnap to remove the optical drive bezel in the direction by arrow e. Removal steps of base cover Remove eight screws a.
Removal steps of base cover continued Remove the two screws b. Make sure that all the connectors are attached firmly. Any other battery could ignite or explode.
Lenovo 300-14IBR (ideapad) Hardware Maintenance Manual Page: 78
Removal steps of battery pack Remove screws athen remove the battery pack in the direction shown by arrow b. The hard disk drive is sensitive to physical shock. Improper handling can cause damages and permanent loss of data.
Removal steps of hard disk drive Remove the four frame fixing screws a. Remove the hard disk drive in the direction by arrow b. Removal steps of hard disk drive continued Remove four screws e c and detach the hard disk TSST SU-228GB ODD from the metal frame in the direction shown by arrow e d. Make sure that the HDD connector is attached firmly.
TSST SU-228GB ODD steps of DIMM Release the two latches on both edges of the socket at the same time in the direction shown by arrows a, and then unplug the DIMM in the direction shown by arrow b.
Push the DIMM firmly, and pivot it until it snaps into the place. Make sure that it is firmly fixed in the slot and difficult to be moved. Refer TSST SU-228GB ODD Table 4. Parts list—Overall on page 62 for Lenovo part numbers for the approved modules.